판매용 중고 REHM V7 Nitro 2.6B #9235989

Reflow oven (6) Heating zones Cooling zone Nitrogen / Air operation Height with open hoods, 86.61" Required area: 7.7 m² Load per unit area: 400 kg/m² Voltage supply Nitrogen Length of inlet table, 9.84" Length of outlet table, 9.84" Length: 102.36" Pin chain conveyor: Conveyor system height: 900 mm ±75 mm / 35.43", ±2.95" Width: Single conveyor ±0.5mm: Min 3.15" (MU-lowest position) / 3.94" (MU-highest position) - Max 15.75" (option 18.11") Dual conveyor ±0.5mm: Min 3.15" (MU-lowest position) / 3.94" (MU-highest position) - Max 8.5" Clearance above conveyor, 1.18" Clearance below conveyor, 0.78" Adjustable conveyor speed: 7.09" - 70.87" per minute Tolerance conveyor speed: <= 0.354" per minute Conveyor system height: 35.43" ±2.95" Mesh belt conveyor: Width mesh belt conveyor: 15.77" Adjustable conveyor speed: 7.09" - 70.87" per minute Tolerance conveyor speed: < 1% Cooling water at external cooling: Connection: M 28 x 1.5 (0.87" Cu tube) Cooling water flow: between 10-20 l/min/158.5-317 gal/hr Operating pressure: 2 bar / 29 psi - 5 bar /145 psi Differential pressure: 0.5 bar / 72.52 psi Voltage supply consumption: Type of power system: 5-wire system (L1, L2, L3, N, PE) Voltage supply: 230/400 VAC ± 5%, 50 Hz Connected load without bottom heating V7 nitro: 44 kW Connected load with bottom heating V7 nitro: 53 kW Connected load +5kW, with internal cooling Operating capacity without bottom heating V7 nitro: 11.0 kW Operating capacity with bottom heating V7 nitro: 13.3 kW Operating capacity +2 kW, with internal cooling Nitrogen supply: Connection: M16x1 (10.472" Cu tube) Nitrogen supply pressure: 6 bar/87 psi - 10 bar /145 psi Operating pressure: 5 bar/72.52 psi Nitrogen consumption (single conveyor at <100 ppm in peak): 25 - 29 m³/h 14.71 -17.06 ft³/min Exhaust: Exhaust socket diameter: 5.91" Exhaust at min 3 mbar under pressure V7 nitro: 600 m³/h/353.36 ft³/min Exhaust temperature: < 50°C / 122°F Exhaust external cooling / warm + clean air: Exhaust socket dimensions: 28.15" x 11.82" Exhaust surrounding temperature: 2400 m³/h /1413 ft³/min Exhaust temperature: < 50°C / 122°F Heating: (4) Preheating zones (2) Peak zones Length of zones: 15.75" Cross profile (Delta T:Tmax thin): ±2.5 Kelvin Permissible soldering temperature Preheating zones, 300°C / 572°F Peak zones, 350°C / 662°F Heat transfer through forced convection Gas circulation per heating zone: 600m³/h / 353.15 ft³/min Cooling zone: Length: 49.21" Warm up time: 30 minutes Specification: 5K / 4 sigma Maximum noise level without internal cooling: 72dBA Maximum noise level with internal cooling: 75dBA Room temperature: between 15°C and 32°C / 59°F and 89.6°F Humidity: between 30% and 75% Oxygen: < 100 ppm in peak zone Center support: Center support V7: link chain, 20mm Center support position: 1.97" - 3.78" (Option 16.14"/18.03") 2006 vintage.