판매용 중고 GLEASON Phoenix 175 HC #9410228

CNC Hypoid cutting machine GE-FANUC 150 MB CNC Controller High speed for dry cutting Cyclovac air assist chip removal system FANUC 60i Computer control Face milling: 216 mm Face hobbing: 190 mm Magnetic chip conveyor LCD Flat color display, 10.4" Cycle fault monitoring Production and sharpen-cutter count display Hydraulic work-piece chuck (With draw-rod and nut) Work spindle bore: 3-29/32 Work-head ratio gears: 5:1 Single-cycle gear finishing arrangement Work chamber lighting Foot switch for hydraulic chucking of work-piece Power forced lubrication system Self contained coolant system (Pump tank and piping) Magnetic chip separator: Chip exit height, 24" Control circuit: 115 VAC, 24 VDC (Input / Output) PHOENIX NFPA 79-1987 Storage capacity for (100) Parts Security key for control of set-up Wiring and hydraulic diagram Extreme ratio: 10:1 Root angle range (B-Axis): -5° to 90° Equivalent root angle range: -5° to 90° Maximum gear pitch diameter: Face hobbing Spiral: 30° TRI-AC Cutter, 6" with (13) blade groups Maximum pitch diameter: 1:1: 6.000" 2:1: 7.500" 5:1: 7.500" Maximum full depth: 0.550" Maximum face width: 1.600" Maximum gear pitch diameter: Face milling Spiral: 35° Diameter cutter, 7.5" Maximum pitch diameter: 1:1: 6.750" 2:1: 8.500" 5:1: 8.500" Maximum full depth: 0.625" Maximum face width: 1.600" Maximum swinging base travel (B-Axis): 5° to 90° Maximum vertical travel (Y-Axis): -4.00" to 7.00" Maximum horizontal travel (X-Axis): -6.00" to 4.00" Sliding base travel (Z-Axis): 2.00" to 12.00" Machine center to work spindle face: 4.500" Tooth number: 5 to 200 Cutter diameters: Conventional face milling: 1.1" to 7.5" HELIXACT TRI-ACT Fine pitch: 102-152 mm Coarse pitch: 152 mm Speed: B-Axis swinging base (Degrees per second): 30°/Sec A-Axis work spindle (Face milling): 240-960 RPM A-Axis work spindle (Face hobbing): 240-960 RPM C-Axis cutter spindle: 380-910 RPM X-Axis horizontal: 4.92"/Sec Y-Axis vertical: 4.92"/Sec Z-Axis sliding base: 4.92"/Sec Work spindle: Diameter of taper at large end: 3-29"/32" Taper per foot: 38"/64" Depth of taper: 3" Motors: B-Axis swinging base: FANUC 5s/3000 Digital servo-drive, 2,000 RPM A-Axis work spindle (Face milling): FANUC 30s/3000 Digital servo-drive, 20,000 RPM A-Axis work spindle (Face hobbing): FANUC 30s/3000 Digital servo-drive, 20,000 RPM X-Axis horizontal: FANUC 5s/3000 Digital servo-drive, 10,000 RPM Y-Axis vertical: FANUC 5s/3000 Digital servo-drive, 10,000 RPM with brake Z-Axis sliding base: FANUC 5s/3000 Digital servo-drive, 10,000 RPM C-Axis cutter spindle: FANUC 1024 15P Digital servo-drive Coolant: 3 HP Hydraulic: 3HP Chiller Chip separator Manuals included Control circuit: 115 VAC with 24 VDC Input / Output Power supply: 380-460 V, 50/60 Hz, 3-Phase 1999 vintage.